Electroboffin
  • 😎VoidBot
    • All Parts
    • MK1
      • Kit Contents
        • Electronics Parts
          • Development Board
            • Arduino® UNO R3
            • Arduino® UNO R4 Minima
            • Arduino® UNO R4 WiFi®
          • 1602 LCD
          • 1602 LCD I2C Module
          • IR Sensor
          • BO Motor
          • F-F Jumper Wires
          • M-F Jumper Wires
          • M-M Jumper Wires
          • 9V Batteries
          • MG90S Servo Motor
          • 9V battery Holder
          • L293D Motor driver shield
          • HC-SR04 Ultrasonic sensor
          • 10 colors Ribbon Wire
        • 3D printed Parts
          • Chassis
          • Wheels (Art Wheel)
          • 1602 LCD Mount
          • Arduino UNO Mount
          • 9V Battery Holder Mount
          • Castor Wheel Mount
          • BO Motor Mount
          • IR Sensor Mount
          • Ultrasonic Sensor Mount
          • SG90/MG90 Servo Motor Mount
          • Raspberry Pi Mount
          • Raspberry pi camera Mount
          • H.P. 3.1
          • H.P. 3.2
          • H.P. 3.3
          • H.P. 2.2
          • M.P. 11.5
          • M.P. 6.3 L
          • M.P. 3.3 L
          • M.P. 3.3 U
          • M.P. 3.3 Z
          • Servo Connector
        • Mechanical Parts
          • Castor Wheels
          • Allen Keys
          • M3X6mm CS Screws
          • M4X8mm Screws
          • M4X10mm Screws
          • M4X12mm Screws
      • Firmware
        • Arduino
          • Arduino UNO R4 Wifi
            • Arduino IDE
              • Basics
              • Line Following Robot
              • Obstacle Avoiding Robot
              • BT Controlled Robot
              • Obstacle Avoiding robot
        • Arduino UNO R4 Wifi
        • Arduino UNO R3
  • 🤖About Me
  • 😍Sponsors
Powered by GitBook
On this page
  • Find me on platforms you Love❤️‍🔥
  • Find ELECTROBOFFIN on platforms you love😇

Was this helpful?

About Me

PreviousArduino UNO R3NextSponsors

Last updated 1 year ago

Was this helpful?

I'm Padmalaya Rawal, an Electronics Engineer cum maker from India. I love to bake and break robots. And before 2020 I was just blowing up ICs, resistors, capacitors and what not. In Nov 2020, I bought my new toy, Ender 3 V2 (a 3D printer) which was not less than an infinity stone for me and begin tinkering with it day and night (All thanks to COVID-19). And in 2022, I started Electroboffin as a blog website and in 2023, I registered "Electroboffin" and turned it into an ecommerce website where I can sell my creations.

Find me on platforms you Love❤️‍🔥

Find ELECTROBOFFIN on platforms you love😇

Why I started building VoidBot?

Robots never fail to fascinate me since my childhood and was always wanted to a robotics engineer but was not able to land at a university that offers Robotics engineering. But for me robotics is just a combination of three pillars viz., Electronics, mechanical and Computer science. So, I started gathering as much information as I can to make my own robots. And I struggled a lot in finding the resources that works for everyone every time. And if any of my friend wants to build the same bot, they again have to mess with the planning again that I did. With VoidBot, I'm trying to solve as many such issues as I can to lower the entry barriers in robotics.

🤖
padmalaya_rawal | Instagram | LinktreeLinktree
Electroboffin | Twitter, Instagram | LinktreeLinktree
Logo
Logo